rolex applied markers misaligned | Misaligned hour hand with tolerance?

2024-11-22T07:08:44 | By , DOD blog

rolex applied markers misaligned | Misaligned hour hand with tolerance? rolex applied markers misaligned Just picked up this 1601 Datejust, circa 1977. Some of the lume and markers are misaligned; the crown too, slightly. Is this normal for this age of Rolex? Should it raise any . $9,999.00

0 · Rolex misaligned markers
1 · Rolex Hour Marker Alignment
2 · Misaligned hour hand with tolerance?
3 · Misaligned diamond hour markers in DD36

Buy and sell authentic used Rolex Datejust watches. Explore great deals from local and international sellers on the Chrono24 marketplace. Financing available in the USA.

As mentioned, it would not be possible to "align" the larger round diamond indices at the hour markers because of the day opening. "misaligned" implies an error, where non . Rolex Hour Marker Alignment. 1. Bezel misalignment on the Submariner/GMTII seem to be a pretty common problem. Not acceptable IMO, but it is seems to be prevalent. 2. .

Just picked up this 1601 Datejust, circa 1977. Some of the lume and markers are misaligned; the crown too, slightly. Is this normal for this age of Rolex? Should it raise any .

Rolex misaligned markers

After, the hour markers are hand-applied into machined holes. I set up a rig to take photos - ruling out as much parallax as possible. Here are some macro shots of my issue, as a . It is impossible to tell whether or not the hand is misaligned as we have no way to tell if this picture was taken square on. The tolerance for the hand setting is 1 minute either side. It .

As mentioned, it would not be possible to "align" the larger round diamond indices at the hour markers because of the day opening. "misaligned" implies an error, where non-aligned for necessity or fitment is common with all small machines. Rolex Hour Marker Alignment. 1. Bezel misalignment on the Submariner/GMTII seem to be a pretty common problem. Not acceptable IMO, but it is seems to be prevalent. 2. Rehaut alignment is another common problem. Gross misalignment is not acceptable either, but a very slight misalignment is understandable. 3.

Rolex misaligned markers

Rolex Hour Marker Alignment

After, the hour markers are hand-applied into machined holes. I set up a rig to take photos - ruling out as much parallax as possible. Here are some macro shots of my issue, as a result of a slightly rotated stamp. The consensus is that the stamped dial seems to be a rotated <<1 deg, clockwise. It is impossible to tell whether or not the hand is misaligned as we have no way to tell if this picture was taken square on. The tolerance for the hand setting is 1 minute either side. It would be better if you set the time to 6 o'clock and that would give you a better indication.

My engraved Rolex Rehauts all align pretty much perfectly to 12 with the little crown engraving. the X in Rolex will hit each marker from 1 - 5. The R in Rolex will hit each marker from 7 - 11. Each of my serial numbers falls between minute marks starting between 26/27 and ending between 33/34 hashes.

The 24 hour hand on the Rolex did not align with the hour indicator when the minute hand was at 1200. There was a good 2-1/2 minutes delay before the 24 hour hand was exactly in line with the hour marker. The watch has been back to the AD three times and to the factory for adjustment.

Rolex Hour Marker Alignment

Anyone expect "perfect" alignment in terms of minute indexes, hour markers and items like crown on a dial? Here's a daytona where the crown on the dial is not perfectly aligned with the 12 hour marker. Looks shifted to the left a little. It's also present on the rolex website.

I got my new 2020 submariner and looking at it, the alignment of everything seemed a little off. After a closer look, it seems like the dial might be rotated clockwise. I was wondering if anyone has had success getting this fixed . "misalignment" of minute/second hands: Intended design feature or QC issue? Rolex General Discussion

Just picked up this 1601 Datejust, circa 1977. Some of the lume and markers are misaligned; the crown too, slightly. Is this normal for this age of Rolex? Should it raise any concerns? Would you accept it or ask for a refund? After, the hour markers are hand-applied into machined holes. I set up a rig to take photos - ruling out as much parallax as possible. Here are some macro shots of my issue, as a result of a slightly rotated stamp. The consensus is that the stamped dial seems to be a rotated <<1 deg, clockwise.

It is impossible to tell whether or not the hand is misaligned as we have no way to tell if this picture was taken square on. The tolerance for the hand setting is 1 minute either side. It would be better if you set the time to 6 o'clock and that would give you a better indication. My engraved Rolex Rehauts all align pretty much perfectly to 12 with the little crown engraving. the X in Rolex will hit each marker from 1 - 5. The R in Rolex will hit each marker from 7 - 11. Each of my serial numbers falls between minute marks starting between 26/27 and ending between 33/34 hashes. The 24 hour hand on the Rolex did not align with the hour indicator when the minute hand was at 1200. There was a good 2-1/2 minutes delay before the 24 hour hand was exactly in line with the hour marker. The watch has been back to the AD three times and to the factory for adjustment. Anyone expect "perfect" alignment in terms of minute indexes, hour markers and items like crown on a dial? Here's a daytona where the crown on the dial is not perfectly aligned with the 12 hour marker. Looks shifted to the left a little. It's also present on the rolex website.